In Phoenix, our heating and cooling bills can account for half of our total utility bill. Learning how to choose and set your thermostat properly can save you hundreds of dollars a year on your utility bills.  The new Nest thermostat developed by ex-Apple employees learns on its own and can be controlled from a Smartphone.  We recently retrofitted a home that had two Nest thermostats and my crew thought it was the coolest thing they had ever seen.  It is very fun to play with and it saves you money too!  

While the rest of the market catches up with Nest, here are some great videos guide to help you choose a programmable thermostat that's right for your lifestyle and schedule.  There are also helpful tips on how to set the thermostat during the day and night.  The second video is from SRP and shows how to install a programmable thermostat.  An SRP energy auditor will also be able to tell you if your thermostat settings are best suited for your home.  APS also gives some helpful advice at the link below.
http://www.aps.com/main/services/business/waystosave/buswaystosave_64.html

Enjoy! 

A high efficiency heating and cooling system does not end with the unit itself.  This is especially true in Phoenix, where most of the ductwork is located in attic space where temperatures can reach 140+ in the summer.  A high SEER AC unit is definitely an improvement when replacing older units, but that air needs to be carried through the ductwork distribution system to keep you comfortable in the winter and summer. 

If the air conditioning contractors cut corners on the ductwork, then the entire efficiency of a new unit is greatly reduced.  In Phoenix, homes built after 1980 used flex ductwork as the preferred means of air distribution.  Flex ductwork is good because it is easy to install, required little preparation and can be done by less skilled workers.  On the down side, unless an air conditioning contractor does a proper load and duct design calculation using Manual J and D, a number of problems can arise because of cutting corners.  Problems such as poor airflow, high room pressures, excessive dust and conditioned and heated air being lost to the outside are all too common in existing homes.  Many times if an air conditioning contractor has done work or replaced an AC unit in the past, they really will mess a system up.  I think one of the reasons good home inspectors and energy auditors are so skeptical of HVAC contractors in Phoenix is because we see the outrageous work done and what it is costing the homeowner.  

Duct leakage can mean your heating and cooling system is sucking outside attic air into the unit and heating it in the winter or cooling it during the summer and blowing air into the attic on the supply side.  Both are costly and will decrease the life of the unit.  APS estimates that an average 15% of a home’s existing air is wasted to the outside.  SRP shows similar statistics and both utility companies sponsor home energy audits to check for leakage and offer rebates for sealing the ductwork.  For more information on duct leakage visit:

http://www.aps.com/_files/services/ResFAQ/ductleakage.pdf

http://www.aps.com/main/green/choice/choice_75.html

http://www.bestofbuildingscience.com/videos.html

http://www.energystar.gov/index.cfm?c=home_improvement.hm_improvement_ducts

http://www.greenintegrateddesign.com/air--duct-sealing.html

1.       You won’t learn any new building science skills.  HERS classes very quickly cover building science concepts and gloss over health and safety and house-as-a-system concepts.  The companies that do HERS training aren’t aligned with the Building Performance Institute to get BPI Continuing Education Credits.  The main purpose of a HERS course is to pass the HERS exam which is more about the SYSTEM in-place for data collection, REMRATE parameters and qualifying entries.  There are questions on the exam regarding heat transfer and building science but a week long class is even more crammed than a BPI class since the instructor has all the building science topics to cover plus new material on HERS.

2.       The costs of travel, lodging, courses, exams, probationary ratings and even finding your own test houses can add up quickly and are all separate costs!  HERS Indexes require a duct blaster test be performed on the home, which is another piece of equipment which needs to be purchased.  Some HERS training classes include 3 probationary ratings during the week long class, but most do not.  There you also have a separate REMRATE software license fee plus the Affiliate fee for third party verification of your work for Energy Star.

3.       The HERS Rating market is focused primarily on new construction, then in the mortgage industry.  There is a great opportunity for energy efficient mortgages (EEMs) but the biggest hurdle is education of realtors and loan officers.  Networking is a great way to meet those professionals but it takes time and persistence to crack that market.  Homes being built to Energy Star standards do require a HERS Index be done but this is a totally different animal than performing energy audits and retrofits on existing homes.  Usually it’s done business-to-business so you don’t have the homeowner aspect anymore which takes out the client interaction during the audit completely. 

Here are the reasons why you should become a HERS Rater. 

1.       Energy Efficiency Mortgages or EEMs is a relatively untapped market.

2.       REMRATE and REMDESIGN are great software tools to know and deepen your understanding of cost effective upgrades.

3.       Code requirements for homes are becoming stricter with minimal duct leakage and better ventilation standards.  RESENET has well positioned itself in the new homes industry and IECC code is headed towards duct tests and/or HERS Indexes be performed on all new homes.  I don’t think this will happen for another 10 – 15 years but by getting your HERS Certification you are ahead of the game.

Just like anything if you are focused on making a successful career as a HERS Rater it takes energy, time and hard work but it can be done and the rewards are huge.  We wish you luck in any endeavor you take and happy 2012!

We have written several articles on what radiant barrier is, does radiant barrier work and why there are radiant barrier scams out there and in this article we will answer the question is there an alternative to radiant barrier?  

The short answer is, YES!  We first strongly suggest that you get an APS energy audit or SRP energy audit to identify and prioritize the best cost-saving upgrades for your home. The APS energy audit is great because energy auditors cannot make the same recommendations for each house (like a radiant barrier company does) and their recommendations are based on their findings of your home’s audit.  Yes, Phoenix does get very hot in the summer, and yes, if you stand under a box with a 100 degree light shining down on your you are going to feel hotter without a radiant barrier than with one and those make for very convincing arguments for radiant barriers but on this occasion don’t let yourself rule out common sense and the FACTS about heat gain into your home.

So what are the alternatives to radiant barrier?  That all depends on the price, assuming you have a quote in your hand for radiant barrier find your estimated cost savings by using our radiant barrier calculator.

Let’s say your radiant barrier costs around $2,500 by itself and from our calculator your savings is going to be $75 a year (do not be fooled into thinking the radiant barrier is going to save more than $200 a year if you live in a home less than 5,000 sq ft).  So if you really are against getting a home energy audit or have a tight home and duct work system, I would recommend a solar hot water heater.  Unlike radiant barriers, there are great APS and SRP rebates available plus state and federal tax incentives that make the cost of a solar water heater equal to a $2,500 radiant barrier!  With a solar hot water heater, your annual savings are in the hundreds of dollars since water heating is usually the second biggest energy user after the heat pump.  Radiant barriers can gather dust after a couple years in the attic, rendering them totally ineffective.  Solar water heaters have 10 year manufacturer warranties plus if your water heater is old, it is replaced with a brand new one.  In Phoenix, solar water heaters can supply hot water during most of the year, even during the winter.  Phoenix solar hot water systems can be very cost-effective with quicker paybacks and ROI than radiant barrier and it is our favorite alternative to radiant barriers.

Green ID offers several types of solar water heaters depending on your existing system and needs.  We offer a free solar hot water assessment of your home to help identify which system is right for your home.  Feel free to give us a call to schedule your free, no obligation assessment today at (602) 684-0462 and we look forward to speaking with you soon.

We have been getting lots of questions regarding radiant barrier products.  Radiant barriers seem to make sense to reduce attic temperatures in the summer. You may have seen the home show demonstrations where one side of a mock attic has a high pressure sodium lamp heating one attic with radiant barrier, and one attic without radiant barrier.  These are very convincing demonstrations that you can actually feel or see the temperature differences.  So does a foil radiant barrier product work?

Let me give you a background of where we are coming from as a US EPA Home Performance with Energy Star energy auditor and contractor.  We use a science based approach to reduce your energy bills and make your home more comfortable.  That means our recommendations are based on a comprehensive energy audit using a blower door, thermal camera, energy modeling and heat transfer principals… not on a PowerPoint Presentation someone developed who probably is not an energy auditor.  We have performed hundreds of APS energy audits and SRP energy audits so we have some experience under our belt and seen the benefits and a home that performs well, and the broken promises that are not only costly but bring down companies that do quality work.  So let’s get back to your question.

Here are the facts -

1.       In Phoenix, with 360 days of sun a year, in a house with minimal insulation your home is only getting a maximum of 20% heat gain from the attic.  We have written about the importance of your insulation being installed correctly in a previous post.  The majority of your heat gain is through the windows.


2.       Using the most outrageous radiant barrier savings claims of a 30% cost savings on your heating and cooling bill (sometimes even the sales rep gets confused and says it’s 30% of your total bills), let’s do the math.  I’ve provided a radiant barrier savings calculator you can use to get accurate estimates on your savings below, just enter in your highest summer electric bill.  Let’s say that’s $300 and 50% of that is from cooling.  So that means you are spending $150 on cooling for, let’s be generous and say May, June, July, August, September (5 months).  $150 x 5 months = $750 on cooling (overestimated).  Then we’ll find how much of your cooling bills is from the attic (20% from #1 above) by taking $750 x 20% = $150.  Now take 30% of $150 = $45.  That’s your annual savings from radiant barrier, $45! 

3.       If you are spending $2,000 on a radiant barrier to save only $45 a year, there are much better ways to save money on your bills!  One would be to install a solar hot water or even solar electric system for a much quicker payment and ROI.  That is why we will never recommend a radiant barrier product without tacking the big items found in a home energy audit first.

We hope that helps and feel free to leave comments below or like us on Facebook for a free Energy Savings Guidebook to learn how you can start saving today.

I know the summer is over in Phoenix and we can now enjoy the beautiful days on the golf course but we do use our furnaces or heat pumps to heat our homes and although not as extreme as the summer, the same HVAC tips I would like to share still can be applied to help reduce your electric and gas bills.

The Phoenix energy audit industry is very much married to the Phoenix HVAC industry because our energy bills are dominated by the costs associated with cooling our homes so I am always conveying important air conditioning tips during my energy audits to help cut those utility bills.  In Phoenix there are two key air conditioning systems that are critical to ensure your system is operating as efficiently as possible and they are refrigerant charge and airflow.

 In Phoenix, air conditioning accounts for 40% - 60% of your electric bill in the summer so it is essential to change your filters regularly.  By changing the air filter you are not only breathing cleaner air but your house gets less dusty and it helps properly circulate the airflow throughout your house.  Good airflow is critical to ensure your HVAC system is operating at its highest rated efficiency.  If not, the HVAC unit ends up working a lot harder than it has to and shortens the lifespan of the air conditioning unit and parts.

Your refrigerant is critical to your air conditioning efficiency because it is the fluid that is responsible for actually providing warm air in the winter and cold air in the summer.  Each air conditioning system has a specified amount of refrigerant it is supposed to have to work at its peak.  Too much refrigerant and your HVAC system becomes overcharged and causes the compressor to work harder and possibly overheat.   Be careful you have a trusted HVAC contractor who is NATE Certified because many air conditioning contractors will purposely add too much refrigerant into your system thinking it will help. 

A refrigerant leak is equally as bad and is usually identified because the home will never reach the set thermostat temperature and your HVAC unit will keep running constantly without cooling or heating.  It is not enough to simply add more refrigerant, homeowners should ask their HVAC contractor where the leak is occurring and have them repair the line. 

During my APS energy audits and SRP energy audits I occasionally run across a home that has high utility bills but as I am going through my inspection of the air leakage, duct leakage, insulation, room pressures, HVAC system and ductwork there is not a huge problem identified.  In one SRP home in Gilbert, I fell back on the homes motors, pumps and appliances and started exploring other options to pinpoint the cause.  During this home’s SRP energy audit the homeowner informed me that she was running the dryer three to four times just to dry a load of laundry.  It can be frustrating when it takes longer to dry your clothes than it does to wash them, especially if you have a couple loads of laundry to do.  I know what that’s like, having bought a 1995 home in Phoenix with all original appliances.  I hated having to run my dryer 3 or 4 times just to get my clothes dry!  If you are in the same situation or you may even have a new washer and dryer set – before you go out to buy a brand new dryer here is a quick tip I found can save you literally hundreds a year on drying costs. 

Your dryer is actually the second biggest energy using appliance after the refrigerator.  Plus if you are having to run the dryer twice or more to get your clothes dry then it is using even more energy.  The washer actually doesn't use that much energy, the costs for the washer come in when it needs to use hot water (try buying cold water detergent and seeing how your clothes come out).  Your dryer vents can be anywhere from a couple inches to 20 feet of ducting to get to the outside.  All that ducting collects lint inside and could clog the vent and decrease the efficiency of the dryer.  By cleaning dryer vents at least once a year you will increase the efficiency of the dryer and help prevent the risk of fire.  A good way to clean the dry vent is to use a shop vac or leaf blower and suck all the lint outside.  You want to be sure to snake the whole system to prevent a buildup.

In this case the SRP energy audit recommendations was mostly around the home’s pool pump run time, recirculation pump, 4 combined refrigerators and freezers and the clogged dryer rather than construction defect upgrades.  This homeowner was still able to take advantage of the SRP rebates available for the variable speed pool pump and the refrigeration recycling program as well as the duct sealing rebates.

Air conditioning in Phoenix accounts for up to 60% of a home’s annual electricity costs.  It is not uncommon for energy bills to double in the summer time in Phoenix even if a homeowner tries to manage his or her energy use by switching to the APS and SRP time of use plan, only doing laundry and running the dishwasher at night, and setting the thermostat up during the day.  Here are seven ways you cans save on air conditioning costs without spending thousands of dollars replacing your AC unit with a high efficiency unit.  

Air Conditioning Saver #1 - Leave your doors open

No, not your exterior doors but your interior doors.  Phoenix air conditioning companies have spread a lot of false information out there about closing your vents and doors.  You want all the interior doors open or at least cracked to help circulate air back to the return.  Here is a quick test you can do to check if your air conditioning costs are higher than they need to be.  With the air conditioning on close a bedroom door and place your hand under the door to check if you can feel air coming out of the door.  If you can feel air escaping, your room pressures are likely to be unbalanced every time the door is closed.  Have an APS Home EnergyAuditor or SRP Home Energy Auditor do a home performance assessment of your home to actually measure the pressure in each room to determine if correction is needed. 

What if you have teenagers or relatives are staying over or you have dogs that you don’t want in a room so you have to keep the door closed.  Your energy auditor will probably recommend a transfer grille or jump duct be installed to relieve the built up room pressure and can go over the options with you.

Air Conditioning Saver #2 - Seal the ductwork.

Between 20% to 30% of an average home in the metro Phoenix area is wasting conditioned air in the summer and heated air in the winter to the attic.  If 60% of your energy bill in the summer is from air conditioning and 20% of that air is not being delivered to the rooms it needs to go to, that can add up to quite a bit of change over 5 years.  HVAC contractors do not seal the ductwork even on a new, high efficiency air conditioner which is like driving a Prius with a hole in the gas tank.  Sealing your HVAC ductwork not only saves money on your heating and cooling bills, it brings less dust in the home too.

Air Conditioning Saver #3 - Air seal your home.

Making sure your exterior doors are well weather-stripped, air sealing any electrical and plumbing penetrations and sealing any recessed canned lights will help keep your conditioned air inside and the outside air outside.  A leaky recessed canned light can increase heating and cooling bills by as much as $5 to $30 per canned light.
Air sealing your home will also help stop the stack effect which causes warm air to rise and cool air to enter the home.  If you have a wood burning chimney, a chimney pillow will help stop heated air from escaping in the winter and save on your winter heating bills.  If you only have some areas of doors that you can see light through there are easy upgrades you can do with filler weather-stripping to fill those voids without replacing your doors.  I know what you are going to say, don’t houses have to breathe?  Yes, you need to have a supply of fresh air into your house for health and safety concerns but it is better to seal your home as tight as possible and bring controlled ventilation in from the outside than live with a leaky home and rely on dirty attic air as your “fresh air” for the house to breathe with.  An APS Energy Auditor or SRP Energy Auditor will calculate theacceptable “breathing rate” of your home and compare that number with the measured “breathing rate” or house leakiness from a blower door test.  

Air Conditioning Saver #4 - Install shade screens in the summer and remove them in the winter

Shade screens help reduce air conditioning costs by blocking up to 90% of the sun’s conductive heat through the windows.  Windows account for more than half of the heat gain into your home just because they are transparent and have almost no insulation value.  If you do replace yourhome’s windows, gas filled, vinyl windows are the way to go.  

Shade screens are typically clipped onto the frame and can be removed during Phoenix’s winter season when we use our heat to get maximum sun exposure to save on heating costs.  APS and SRP also give rebates for shade screens if you don’t already have them.

Air Conditioning Saver #5 - Go up to R-38 insulation in your attic

Is it a big surprise that Phoenix attics can get hot in the summer?  That huge temperature difference between the attic and the house is another cause of rising air conditioning costs.  Against popular thought though, the notion that the quantity of insulation is more important than the quality is completely wrong.  It is more important how the insulation was installed than how much you have and a home energy auditor will be able to properly assess your home and tell you how much higher your air conditioning bills are than they should be.

Air Conditioning Saver #6 - Check if there is a direct connection from your garage to the house.

This is not a commonly talked about cause of high air conditioning costs but I have found this problem in houses in Glendale, Scottsdale and Gilbert.  The garage is another area that can get very hot in the summer and like I said before, temperature differences are the main driver of heat gain into homes.  Using a blower door, your energy auditor will be able to test the house-to-garage connection that occurs above the drywall where you cannot see and estimate the heating and cooling loss occurring from the problem.

Air Conditioning Saver #7 - Have your air conditioning unit tuned-up annual by a trusted HVAC contractor. 

I personally know that finding a reliable HVAC contractor can be difficult.  Even though you have a friend in the air conditioning business does not mean they will do a good job.  I have been in too many homes where an AC contractor and friend installed a new unit and probably not purposely, but unfortunately cut way to many corners simply because that’s the way it’s been done for the last 20 years.  After that is done, fixing any of their work is 10 times more difficult.  First, the homeowner doesn’t want to point fingers at their buddy’s work, second the homeowner probably doesn’t know what “correct” looks like.  Like a good handyman, every homeowner should have a good HVAC contractor.

Those are the 7 ways you can reduce your air conditioning costs dramatically.  For others ways to save money on your utility bills be sure to check out our past articles and get up to speed on APS energy audits and SRP energy audits for your home.

If you have had an APS energy audit or SRP energy audit performed on your home the auditor probably showed you the blower door readings or thermal images of your canned lights.  These are notoriously leaky and if a smoke pen is held up to the light, you can see the smoke gets easily sucked right up into the attic through recessed light.  If your home has more than 10 of these recessed lights, it can be a significant source of air leakage in your home.  The average home wastes about $5 to $30 per year per recessed light so it is an important cost savings consideration and health and safety concern if moisture escapes into the attic as well. Here is a little background on these lights and what you can do to stop excess air leakage in your home.

Recessed lights are typically installed in areas of high traffic areas like kitchens, hallways and family rooms.  Canned lights are either IC rated, insulation contact rated, or non IC rated, which cannot come into contact with insulation.  If additional insulation has ever been added to your home you may want to check that the insulation contractors put some sort of protector around the light before blowing more in.   Typically in homes built before 1995, non IC canned lights were used but I have seen plenty of newer homes with non IC rated canned lights installed.  You can find out if your lights are IC rated by going in the attic and looking at the nameplate of the metal light.  There is usually a label glued on top of the light that says the specifications of the light and it will say, “IC Rated”. 

Recessed lights in a two story home can also contribute to the stack effect if there are enough lights in the ceiling.  The stack effect is when warm air rises and is replaced by cool air entering the home through outside penetrations and duct leakage.  The stack effect and air leakage can be stopped by air sealing the home including the canned lights.  To find more information on how canned lights can contribute to the stack effect in your home check out this article by the Pennsylvania Housing Research Center.

There are several ways you can effectively seal your canned lights by either replacement or retrofit.  Replacement options can be done with air tight LED lights or air tight recessed canned lights.  Both replacements are very effective, the advantages of LEDs are a longer lifespan, are fully dimmable, and use less energy.  Replacements done with air tight recessed lights are also very good.  I recently performed an energy audit on a home built in 2006 that had the new air tight recessed lights and can verify that the leakage of the light is very low.   The reading from the canned light you see on my manometer is 0.9 Pa and a typical canned light measures at 40 Pa, which is a lot of leakage.

The other option is to build energy lids with at least 3-inches of clearance between the light and the box.  The energy lid can be fitted over the canned light and sealed at its edges.  Warning!  Do not use expanding foam to seal a canned light; the foam can drip down into the house and on the trim.  The energy lids can be effective if you have non IC rated recessed lights and need to add more insulation to your attic.  You can view more tips on how reduce your energy bills here.

For a guide on ways to seal up your home check out Energy Star’s publication on air leakage and air sealing your home.

SRP has come out with great rebate programs and solidified their commitment to 1) energy retrofits upgrades like duct sealing and insulation, 2) renewable energy products like solar panels for electricity and hot water and finally for 3) switching out old appliances.  Each of these rebate programs are separate entities that sometimes get confused since they are always changing.  For example, SRP solar rebate program has seen better days when solar electricity rebates used to be at $3.00 per watt.  Every couple of months for the last 2 years SRP has dropped their solar rebates until the current amount of $1.45 per watt.  Now the best and most affordable way to get solar is through a solar lease program that significantly buys down the costs of solar panels.

SRP Home Energy Audit Rebates

Now the hot program is SRP’s and APS’s Home Performance With Energy Star.  This is a national Energy Star program to make homes more healthy, comfortable and efficient.  APS and SRP adopted the program to ensure a whole-home approach to reducing energy bills while keeping homeowners safe and with better indoor air quality.  SRP requires a $99 energy audit be performed on a home to diagnose the causes of high energy bills, uncomfortable rooms or excessive dust.  Once the audit is complete a report will be generated using building modeling software that gives cost savings for each upgrade.  The SRP rebates will help pay up to $925 (or more if you have two or more AC units) off the costs of the energy retrofit.  The rebates for the Home Performance With Energy Star program are broken down below.

Duct sealing 75% off up to $175 per unit.  For most homeowners, 20% of their heating and cooling bill is wasted from duct leakage.

Air sealing 75% off up to $250.  Air sealing work can be complex as your auditor must determine 

Insulation75% off up to $250

Shade screens $0.80 per sq ft up to $250

SRP has a great visual summary of their rebate program here.

http://www.srpnet.com/energy/powerwise/savewithsrp/homecheckup.aspx

http://www.srpnet.com/menu/energy.aspx

http://www.energystar.gov/index.cfm?fuseaction=hpwes_profiles.showSplash

SRP rebates for pool pumps

$200 for variable speed pool pump.  Each pump has to be calibrated to your pool to ensure that it is not over turning your pool.  This upgrade will reduce your bills $200 - $350 per year.  SRP also provides a $75 rebate for pool timers. For more information on SRP Pool Pump and Timer Rebate see the following link.

http://www.srpnet.com/energy/powerwise/savewithsrp/poolpump.aspx

SRP Rebates for AC units

Air conditioning systems have become more efficient from federal standards and better technologies.  Surprisingly, SRP does not overlap its duct sealing rebates with its air conditioning rebates.  With every unit we install, we include a whole home duct seal to maximize the high efficiency AC unit with a properly sealed duct system, otherwise it’s like using an umbrella with holes in it.  SRP will help you pay for a higher efficiency AC unit depending on the efficiency ratings.  In the AC efficiency world there is a SEER rating, the seasonal energy efficiency ratio, EER rating, the energy efficiency ratio, and HPSF or .  In Phoenix, the EER is a more important number to pay attention to because of how hot it gets here.  The EER ratio gives a better idea of how an AC will perform under very hot conditions (100 degrees) were the SEER rating gives an idea of performance under milder conditions (89 degrees).  SRP recognizes and awards a higher rebate with higher EERs in their AC rebate program.

SRP also has a quality installation standard similar to the post test done for the home energy audits that has to be met when installing heat pumps and furnaces in the Phoenix area also.  Only SRP qualified AC companies can apply for their rebate for you, but not all of them will perform a duct testing and sealing upgrade.  These rebates and companies are separate from the solar rebates and the home energy audit rebates.  All the SRP approved AC companies are required to do a sizing calculation called the Manual J calculation.  You should ask to see the results from your own home to ensure this was done.  The AC rebate program also includes a check of the refrigerant charge to make sure that the unit is properly charged to manufacture specifications and a check of the air flow.  Below is a list of the AC rebates available from SRP.

SEER 15 with EER 12.0 receives $200 SRP rebate

SEER 16 with EER 12.0 receives $300 SRP rebate

SEER 17 with EER of 12.0 receives $400 SRP rebate

All units must be installed by and SRP approved AC contractor.

All contractors must perform a Manual J calculation to properly size the unit (you should verify this since it is not something a typical contractor will do).

All contractors should properly charge the unit and check airflow.

For more information on SRP AC rebates, check out their link here.

http://www.srpnet.com/energy/powerwise/savewithsrp/CoolCash.aspx

SRP Solar Rebates

SRP solar rebates are divided into solar electricity rebates and solar hot water rebates.  Solar electricity for my home was my dream growing up and has proven to be an attractive idea to thousands of homeowners across the Phoenix valley.  SRP perhaps did not realize how attractive solar electricity would be since they have lowered their rebate amount dramatically since its inception.  As of September 2011, SRP solar electricity rebate is at $1.35 per watt.  You can view their current budget and remaining monies available at the link below.

http://www.srpnet.com/environment/earthwise/solar/solarelectric.aspx

SRP Solar Hot Water Rebates

After City and County applications have been approved, SRP does random inspections of the installation.  The solar hot water system must be SRCC rated and have proof onsite.  The first 5 feet of your hot and cold water piping should be insulated to at least R-2.6.  The panels must be un-shaded during the day for the entire year.  The SRP solar water heater rebates are currently at $0.45 per kWh of estimated first year savings (based on the OG-300 ratings), up to 505 off the system’s cost.  The OG-300 rating system is based on the manufacturer’s rating by the Solar Rating and Certification Corporation.  Also important to consider for solar hot water systems is the federal tax credit of 30% off the cost and Arizona state tax credit of $1,000, which makes solar hot water much more attractive.  Typical solar hot water rating systems are around 2,890 kWh per year.  An example rebate table is shown below.

Solar Hot Water Cost $5,400

SRP Solar Rebate $1,300

 Arizona Tax Credit $1,000

Federal Tax Credit $1,620

Net Cost $1,480

Annual Savings $425

Simple Payback 3 years